Make your own free website on Tripod.com


> AT Set > Binary Table > BRI > IP Address > OSI Model > Server Side



 

This is the ISDN AT (ATtention Code) Command Set. I hope it will prove useful to you.


 

ISDN ATtention Code Command Set!
Command Description Possible Values
>D0= Sets the Date 6 digits (MM/DD/YY)
>D1= Sets the Time 6 digits (HH:MM:SS)
>V1= View Switch & Global
Parameters
G - View Global Parameters
C - SPIDS, DNs & TEIs
>F Load Switch Options from
Quick Setup factory profile
-
>W Saves ISDN Switch & Global
Options to stored Profile.
-
>Z Restores Switch Options
from to stored profile & restart
network.
-
!CO= Switch Type. 0-AT&T 5ESS
1-Northern Telecom DMS-100
2-National ISDN (Default)
!C1= Switch Sotware Version. !C0=0: 0-AT&T Point-to-Point
       1-AT&T Multipoint
!C0=1: 2-DMS 100 PVC IC-0
       3-DMS 100 PVC IC-1
!C0=2: 4-National ISDN 1 (default)
!C6= Data SPID. Range: 0-20 characters default (null string)
*1!C6= Voice SPID 1. Range: 0-20 characters default (null string)
*2!C6= Voice SPID 2. Range: 0-20 characters default (null string)
!D3= SAPI-0 Data TEI. Range: 0-63,255 (auto),
127 (disable) default (255)
*1!D3= SAPI-0 Voice TEI 1. Range: 0-63,255 (auto),
127 (disable) default (255)
*2!D3= SAPI-0 Voice TEI 2. Range: 0-63,255 (auto),
127 (disable) default (255)
!N1= Data Directory Number Range:0-20 characters (0-9,#,*)
default (null string)
*1!N1= Voice Directory Number 1 Range:0-20 characters (0-9,#,*)
default (null string)
*2!N1= Voice Directory Number 2 Range:0-20 characters (0-9,#,*)
default (null string)
!V3= Conference Feature Value Range: 1-63, default (60)
!V4= Drop Feature Value Range: 1-63, default (62)
!V5= Transfer Feature Value Range: 1-63, default (61)
!V3= Drop Feature Value Range: 1-63, default (63)
%P1? Displays Software Password -
%P1=x Sets Software Password to x Range: 0-8 alphanumeric characters
default (null string)
%P1=D Disables the Softload
function. To enable Softload, set
the password again.
D, case sensitive
$Q Requests Softload Version Information -
$Y=x Initiates Softload with
Password x
-
En Local Echo Off n = 0 Echo Off
n = 1 Echo On (default)
Qn Status Displays n = 0 Status On (default)
n = 1 Status Off
n = 2 Status off during answer mode.
Vn Verbose n = 0 Numeric
n = 1 Verbose (default)
Wn Carrier/Protocol Result
Codes
n = 0 Disables(default)
n = 1 Enables
Xn Connect Messages
Codes
n = 0 Enables result codes 0-4
n = 1 Enables 0-5,10-15,
17-19,28,32
N = 2 Enables 0-5,7,10-15,
17-19,28,32 (default)
S0= Rings Until Answer Range: 0-255 default(1)
S1? Ring Count (Read Only) Range: 0-255 default(0)
S2= Escape Character Range: 0-127 default(43)
Range: 128-255 Disabled
S3= Carriage Return Character Range: 0-127 default(13)
S4= Line Feed Character Range: 0-127 default(10)
S5= Backspace Character Range: 0-127 default(8)
S7= Wait for Connection Range: 0-255 default(30)
Units = seconds
S7= Wait for Connection Range: 0-255 default(30)
Units = seconds
S10= DCD Drop Time Range: 0-255 default(14)
Units = 1/10 seconds
S12= Guard Time Range: 0-255 default(50)
Units = 1/50 seconds
S18= Test Timer Range: 0-255 default(0)
Units = seconds
S25= DTR Detect Time Range: 0-255 default(5)
Units = 1/100 seconds
S26= RTS to CTS time Range: 0-255 default(1)
Units = 1/100 seconds
&Cn Data Carrier Detect n = 0 Always On
n = 1 Tracks Connection (async only) - default
&Cn Data Terminal Ready (DTR) n = 0 Ignore DTR (synch/sync)
n = 1 Recall ACU (async only)
n = 2 Hangup - auto answer disabled while DTR down (async only) - default
n = 3 Hangup - reset port
9 DTR Dial
&Ln Persistent DTR Dialing n = 0 Disables (default)
n = 1 Enables
&Mn Sync Mode n = 0 Async (default)
n = 1 Sync-DTR disc delay (S25)Sync-DTR dialing (auto answer disabled while DTR down)
&Rn Clear to Send (CTS) n = 0 CTS follows RTS
n = 1 CTS Always on when on-line (default)
&Sn Data Set Ready (DSR) n = 0 DSR always on (default)
n = 1 DSR on after protocol installed except test modes
&Yn Selects Powerup Stored Profile n = 0 Selects stored Profile 0 upon powerup or DTR reset (default)
n = 1 Selects stored Profile upon powerup or DTR reset
&Zn= Stores Telephone Number n = 0-9
0-40 characters (0-9,#,*)
A Answer -
D Dial S=n Dials Stored Number n 0-9,#,* Digits
; Stay in command mode (P,T,W and comma are ignored)
>P="password" (CHAP only)
H Hangup -
In Information n = 0 Product ID
n = 1 ROM Checksum
n =2 Checksum verification
n = 3 Revision
n = 4 Numberic Capability String
n = 8Verbose Capability String
n = 9 Plug & Play ID
n = 10 ISDN Link status
O Returns On-line -
@MENU Invoke Localmenu -
Zn Reloads Port from stored profile n n = 0,1
&Fn Loads Port from Quick Setup factory profile n n = 0-3
&Tn Test Modes n = 0 End Test
n = 1 Local Loopback
n = 3 Digital Loopback
n = 8 Bilateral Leepback
&H Help Command -
&H= Help for Individual Command Enters individual commands for which help is desired.
AT&H=cmd[,cmd...]
&V View Port Parameters -
&V= View Parameters E V.120 Parameters
Z Stored Telephone Numbers
&Wn Saves active to stored profile n n = 0, 1
%E0= V.120 Maximum Transmit Frame Size Range: 1-260 default (256)
%E1= V.120 Maximum Receive Frame Size Range: 1-260 default (260)
%E2= V.120 Window Size Range: 1-127 default (8)
%E3= V.120 Transmission Timer Range: 1-255 default (5)
@N0= Caller ID Logging 0 = Disable (default)
1 = Enables
@N1= Caller ID Auto Delivery 0 = Disable (default)
1 Enables
@Ln Caller ID Number Clearing and Retrieval 0 = Clears the list of numbers
1 Retrieves most recent number
2 Retrieves the entire list
@IS= Caller ID Screening & Blocking D Disables Security (default)
S Enables Screening
B Enables Blocking
@IA= Adds the given ID to the Security ID List -
@ID= Deletes the given ID from the Security ID List -
@IC Deletes all IDs -
@IL Lists Caller ID Security status for the port; list all stored IDs -
@IP Copies the Security status and Security list from the current port to all data ports -
@IV Copies the Security status and Security list from the current port to all analog ports -